MIDI sync interfaces from Phil Rees

Phil Rees MIDI sync interfaces

MDS MIDI to DIN SYNC (Sync24) CONVERTER

Synchro systems

When pieces of music technology equipment are required to work together, a means may be required synchronise them.

The MIDI standard includes a group of single-byte messages called System Real Time (SRT), four of which are concerned with synchronisation (Clock, Start, Continue and Stop).

The Sync24 system was introduced by the estimable Japanese company, Roland (who have both a UK website and a US website). The system was subsequently adopted by a few other manufacturers, but was then largely superseded by the sync facilities of MIDI. Sync24 is popularly known as `DIN Sync', because it uses the round five pin DIN connector, coincidentally the same as is used for MIDI.

Although they use the same type of connector, you should never connect MIDI sockets to Sync24 sockets.

Clever converter

The Philip Rees MDS MIDI to Sync24 Converter listens to an incoming MIDI SRT clock stream and generates a corresponding Sync24 (DIN sync") format output. The MDS appears as a tempo slave to your MIDI system, and is a tempo master in Sync24. When you have installed your sync converter, your Sync24 device(s) should start, play in time, and stop automatically, by remote control from your MIDI master equipment.

The MDS has a MIDI In port, for which a handy MIDI Thru socket is provided.

The MDS has a single Sync24 Sync Out socket. The signals have good drive capability, and we have not found any compatibility problems. The Sync24 output is able to drive several Sync24 inputs in parallel. To make use of this you will probably need a special multi-drop cable assembly. Some Sync24 devices, notably the MC202, have a built-in fan out capability to drive extra slave units.

Continue facility included

As well as regular Start and Stop commands, MDS implements the MIDI Continue command and the Sync24 feature. Compatible Sync24 devices, such as the MC-4, should resume correctly via the MDS.

Some devices, including the MC-202, respond to a Continue by resuming from the beginning of the current `measure'. You may be able to arrange that your master MIDI sequencer always restarts from the beginning of a measure. You can probably manually set both sequencers to start at the same measure. Alternatively you could always to restart the sequence from the top.

The Continue facility is not included on some Sync24 devices. When it is omitted, the Continue command will cause the slave to start the sequence from the very beginning.

Sync interface application

In the diagram above, a normal MIDI cable connects the MIDI Out socket of the computer to the MIDI IN of the MDS. The computer has been set to run off its own internal clock. Also, MIDI Timing Clocks Out has been enabled in the computer sequencer program. The beat lamp should be flashing, which indicates that the MDS is receiving a stream of MIDI clocks from the computer.

The MIDI THRU output of the MDS is connected to the MIDI In on the sythesiser. The SYNC OUT port of the MDS is linked to the Sync port of the old drum machine with a suitable DIN to DIN lead (that is a pin-to-pin cable with pins 1, 2, 3 and 5 connected). The Sync24 port of the drum machine should be set to Input mode.

When the sequencer is running, the computer will transmit Channel Voice and SRT messages. These arrive at the MIDI IN port of the MDS, and are duplicated at the MIDI THRU port. When the Channel Voice messages arrive at the synthesizer they are rendered as musical notes. The synth ignores the SRT messages.

The sync converter ignores the Channel Voice messages, but it uses the System Real Time messages to derive the Sync24 signals which it presents at its SYNC OUT port. These signals go forward to the analogue drum machine, so that it plays its internal rhythm patterns in time with the master sequencer.

The MIDI connection between the Out on the synth and the In on the computer males possible the recording of tracks on the computer sequencer.

Shine a light

The `POWER' lamp (on the front panel, next to the mains lead inlet) is lit when power is connected to the MDS.

The funky `BEAT' lamp (on the front panel, next to the SYNC OUT socket) flashes on and off in time with the sync stream.The lamp is lit for the first quaver-period of every crotchet-period. It will flash four times during a normal common time (⁴₄) measure.

The case of the unit is 109mm x 109mm x 40mm - the MDS is exceptionally compact, particularly when you consider that it contains an integral mains power supply, obviating the need for batteries or an external adaptor

Pris i Norge: 1.490.- (inkl. mva.)

MIDI!

to top of this page

Pan Lydstudio AS, Valstadsvingen 2 (Boks 77),
2013 SKJETTEN. Tlf.63 84 33 30 (12-16) fax. 63 84 49 70

Profesjonelt lydstudio. CD-opptak og produksjon. Salg av keyboards, Hammond & Leslier, musikk & data-utstyr, software, nytt og brukt musikkutstyr. Utleie og reparasjoner.

© Copyright Pan Lydstudio 2001